Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
ok,after the 5 week wait i have just had to get these gaz coilovers i have removed the old spring from the standard strut,binned the rubber bit on the standard spring seat and fitted as they came off but on to my new coilover strut,on top of the black coil spring seat,but the standard spring seat seems to press down on the coilover one not allowing it to pivot,it is doin my head in so much,thought i had made sum progress when they arrived but seems tht i have them sitting at home but cant use them,they seem as if they are too tight or too slack,no inbetween,just cant seem to get them right,have any of u got any suggestions or pics,thanks,Liam
|
Jake
Member
Registered: 24th Jan 05
User status: Offline
|
we need pictures
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
http://www.corsasport.co.uk/board/viewthread.php?tid=361013
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
it looka pretty much like the one there,but has the big metal spring seat which came with standart strut?
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
ant that is what is pushing down when tight on my top coil cup?
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
do u still want a pic m8?
|
Jake
Member
Registered: 24th Jan 05
User status: Offline
|
Yeh. show us a picture of what you have done
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
coilover spring seat isnt meant to pivot.
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
but it seems v stiff,do u mean top or bottom?
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
remove the standard metal spring seat, its no use keeping it. to help it pivot a bit easier get 2 stainless washers and grease them up well. place these between the Gaz top spring cup and the metal standard cone bit. stops wear over time.
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
then wat about the bearing
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
dont need it. the 2 washers will act as a bearing.
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
but wont it wear?between the silver cone thing and the top coil cup,there seems to be a gap of about 4 mm?is the washers the correct way or am i just bin took 4 a mug?
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
think you have fitted something wrong somewhere. once the topnut has been tightened right up there wont be any gaps.
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
washers dont seem as gud as bearings,these were meant to be a str8 fit
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
they are if you fit them properly. Maybe get a Garage with experience of coilovers a try of fitting them.
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
nah av sorted it,instead of bodjing them with washers i popped the old bearings out of the old top seat,all looks ok now,what a farse
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
you did make it more difficult than it had to be
|
Ingram11
Member
Registered: 6th Jun 07
User status: Offline
|
omg,and why is that
|