Torsa g
Member
Registered: 20th Sep 07
Location: Tamworth. Rides: An OSTRIDGE
User status: Offline
|
Hi Ladies
Just looking for some advise on how to stop my car surging when i go round a couple of tight bends, its like i have a gogo gadget smoke screen, the car runs fine and doest smoke at all, but every now and then this happens,
any suggestions
|
Ste L
Member
Registered: 3rd Jul 06
Location: Manchester Drives: 106 16v Rallye
User status: Offline
|
breath mod on rocker cover...
|
Torsa g
Member
Registered: 20th Sep 07
Location: Tamworth. Rides: An OSTRIDGE
User status: Offline
|
will this stop the oil going in to the bore
|
craig_s
Member
Registered: 5th Mar 06
Location: Birmingham Drives: mk4 astra gsi
User status: Offline
|
yep you can either drill a few holes in the plate or cut most of it out and leave a small peice in by where the 2 breather pipes connect.
[Edited on 28-05-2008 by craig_s]
|
johnhara1
Member
Registered: 19th Oct 06
Location: Newcastle upon Tyne
User status: Offline
|
You can block the little breather pipe for a start.
Then do the rocker cover mod. There's guides and info on Migweb and Vauxsport.
Mine had both of the above done and still did it occassionally (but reduced) so i stuck a catch tank on it and it was fine 
|
Torsa g
Member
Registered: 20th Sep 07
Location: Tamworth. Rides: An OSTRIDGE
User status: Offline
|
quote:
Originally posted by craig_s
yep you can either drill a few holes in the plate or cut most of it out and leave a small peice in by where the 2 breather pipes connect.
[Edited on 28-05-2008 by craig_s]
wat plate are you on about craig, not to clued up on this breather stuff, could you go into mre detail
|
johnhara1
Member
Registered: 19th Oct 06
Location: Newcastle upon Tyne
User status: Offline
|
Take rocker cover off and flip it over.
Theres a thin plate thats mounted to the under side.
MAKE SURE YOU CLEAN THE SWARF OUT PROPPERLY BEFORE RE-FITTING!
[Edited on 28-05-2008 by johnhara1]
|
Ste L
Member
Registered: 3rd Jul 06
Location: Manchester Drives: 106 16v Rallye
User status: Offline
|
|
Torsa g
Member
Registered: 20th Sep 07
Location: Tamworth. Rides: An OSTRIDGE
User status: Offline
|
thanks ste ill try this
and John thanks to
[Edited on 28-05-2008 by Torsa g]
|
Ste L
Member
Registered: 3rd Jul 06
Location: Manchester Drives: 106 16v Rallye
User status: Offline
|
this is the plate that you need to remove
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
quote:
Originally posted by Torsa g
will this stop the oil going in to the bore
no. if oil is going in the bores then you have further problems.
|
Torsa g
Member
Registered: 20th Sep 07
Location: Tamworth. Rides: An OSTRIDGE
User status: Offline
|
i mean reaching the bore , as in running through the inlet and making it smoke for about 15 secs till you clear it out
|
Torsa g
Member
Registered: 20th Sep 07
Location: Tamworth. Rides: An OSTRIDGE
User status: Offline
|
this will be done tonite
|
Ste L
Member
Registered: 3rd Jul 06
Location: Manchester Drives: 106 16v Rallye
User status: Offline
|
yes, should prevent oil getting into the tb, and thought the inlet system
|
