Ricky352
Member
Registered: 6th Apr 07
Location: Lisburn, N.I.
User status: Offline
|
Tried this last night, but didnt get far.
Took the plastic trim off from underneath the door, then went to take the bolt out, but ended up taking all the grip out of the bolt instead.
Anyway, Im hoping to get that sorted later, but where are the rest of the bolts? I couldnt see much at all.
Cheers
|
Ellis
Member
Registered: 11th Sep 07
Location: Aberdeenshire
User status: Offline
|
Do you need the seats and frames completely removed?
|
Ricky352
Member
Registered: 6th Apr 07
Location: Lisburn, N.I.
User status: Offline
|
Well Im taking the carpet out, so probably
|
Ellis
Member
Registered: 11th Sep 07
Location: Aberdeenshire
User status: Offline
|
I think there are only 4 - one at each corner almost if you hear where i'm coming from...
|
Ant
Member
Registered: 12th May 02
Location: Hereford and Worcester
User status: Offline
|
only 2 bolts hold it in one under the trim and one towards the centre of the car, its a good idea to spray them from underneath with wd40 and leave for a few days as they normally seize
|
Ricky352
Member
Registered: 6th Apr 07
Location: Lisburn, N.I.
User status: Offline
|
Cheers
|
Fonz
Premium Member
Registered: 12th May 06
Location: Newbury, Berks
User status: Offline
|
http://www.corsasport.co.uk/board/viewthread.php?tid=247763
shows four screws.
that is when i had a go and you can see the two locations nearest the door
|
luke85
Member
Registered: 26th Nov 07
Location: Chesterfield
User status: Offline
|
Its only 2 screws if you take the subframes out though. Its easier to take the seats and subframes out as one rather than take the seat off as above.
Mave sure you have the right torx socket though because theyre gonna be a real pain if you start rounding them off, the WD40 idea is a good one
|
Ricky352
Member
Registered: 6th Apr 07
Location: Lisburn, N.I.
User status: Offline
|
That great guys, thanks, but where would the two screws be if i were just to remove the subframes and seats as 1?
Is there a such thing as a t35 torex bit? t30 seems slightly small and t40 is too big.
|
luke85
Member
Registered: 26th Nov 07
Location: Chesterfield
User status: Offline
|
Yeah there is a T35 bit, you slide the seat fully forwards and the screws are in the runners behind the seat. Once youve got them out you lift the back of the seat a bit and slide it forward and it will unhook its self from the front
|
luke85
Member
Registered: 26th Nov 07
Location: Chesterfield
User status: Offline
|
The one on the inside next to the handbrake is in the centre of the runner where Ive circled and the one near the door is behind the runner, the same bolt that holds the back of the pre-tensioner
[Edited on 20-08-2008 by luke85]
|
Ant
Member
Registered: 12th May 02
Location: Hereford and Worcester
User status: Offline
|
dont forget to put the safty fork in the pre tensioner, there not cheap to replace if it goes off
|
Gareth F
Member
Registered: 16th Jan 08
Location: Location Location
User status: Offline
|
£10 from my local scrappy (in full working order) something stupid from vauxhall £200 plus?
[Edited on 20-08-2008 by munk3yrac3r]
|
Gareth F
Member
Registered: 16th Jan 08
Location: Location Location
User status: Offline
|
Cheaper to put the fork in tho
|
Ricky352
Member
Registered: 6th Apr 07
Location: Lisburn, N.I.
User status: Offline
|
My mate had to pay £30 from a scrappy for one lol
Got the seats out last night, ive left in the subframes and im just going to paint around them. Have lifted all the carpet, just need a heatgun for the sound deadening now.
Appreciate the help folks
|