Camo
Member
Registered: 1st Mar 09
Location: Norn Iron
User status: Offline
|
rite i was under the car the other day and notice that the rear bumper isnt held on newhere underneath other than the screw in the arches and the 4 screws up top, i checked my mates corsa and it has like a second skin that 4 screws go into underneath
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
oh really
|
Camo
Member
Registered: 1st Mar 09
Location: Norn Iron
User status: Offline
|
sorry post replied before i could finish lol, some tw*t has put the bumper on with out this or is it attached 2 the bumper and the whole bumper needs replaced ne idea's??
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
can you not just screw it on as it is?
|
Camo
Member
Registered: 1st Mar 09
Location: Norn Iron
User status: Offline
|
nothing 2 screw it into or cable tie it 2
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
oh right
mine has just one skin then it screws into the crash bar i think
|
Camo
Member
Registered: 1st Mar 09
Location: Norn Iron
User status: Offline
|
hmmm could be missing the crash bar im thinking, need 2 get the bumper off and have a look and see cheers neway
|
adz_gsi
Member
Registered: 20th Sep 08
User status: Offline
|
pre or post facelift as mine has srews in arches on top of bumper then 4 screws under on little tabs that screw into a plastic thing
|
Camo
Member
Registered: 1st Mar 09
Location: Norn Iron
User status: Offline
|
yea it facelift, yip 4 screws that go into a plastic thingy lol just need 2 knwo wat it is
|
Markus
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 19th Nov 07
Location: Beverley - East Yorkshire
User status: Offline
|
self tappers ftw
|
Camo
Member
Registered: 1st Mar 09
Location: Norn Iron
User status: Offline
|
but will be self tapping it into nothing
|
Markus
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 19th Nov 07
Location: Beverley - East Yorkshire
User status: Offline
|
im sure you can make something, does it really matter is the bumper going to fall off ?
|
Camo
Member
Registered: 1st Mar 09
Location: Norn Iron
User status: Offline
|
prob not but its banging and making a noise ffs which is move of a pain in the ass lol
|
andyc1234
Member
Registered: 7th Nov 06
Location: Lancashire
User status: Offline
|
really dont get what your on about here the bumper screws into the metal of the car body underneath if it not there then its been cut off its not a part of the car you can unbolt its a welded pannel
|
Richardhhha
Member
Registered: 29th Sep 07
Location: Croydon, Greater London
User status: Offline
|
The car is sposed to have 3 at the top and 1 in each corner in the wing. Then 4 underneath.. They screw into the rear panel. Whip the bumper off because if what your saying is right then the cars rear panel has been cut which is a big no no
|
andyc1234
Member
Registered: 7th Nov 06
Location: Lancashire
User status: Offline
|
did you manage to get your pannels sorted richard?
|
Richardhhha
Member
Registered: 29th Sep 07
Location: Croydon, Greater London
User status: Offline
|
i am having a chat with a company about the floor pan but the other bits like the rear panel and the rear panel suport (bit that holds the latch pin in place) i can get easely and pritty cheaply. other than that im now pulling off that tar crap, decided to use hammer and chisel then put the thinners on it to get rid of the resedue.. should be easy after that.. also been reading up on not having to weld serten places (will weld the floor in place lol or use pop rivits to save a little weight and bond it into place aswell.) loads of different bonding methods used that are classed as ok by repteble companys
[Edited on 27-05-2009 by Richardhhha]
|