kylesri
Member
Registered: 13th Jan 10
Location: Technician At Perrys Vauxhall Canterbury Kent
User status: Offline
|
anybody no whats this plug is for

cheers kyle
[Edited on 20-01-2011 by kylesri]
|
ianofbhills
Member
Registered: 10th Feb 01
Location: newcastle
User status: Offline
|
Can you get a better pic?
The late dis pac looms have the switched live around there but i cant quite see the plug.
|
kylesri
Member
Registered: 13th Jan 10
Location: Technician At Perrys Vauxhall Canterbury Kent
User status: Offline
|
can try i was told it goes to the oil level sensor in the front of the oil sump the reson is my looms been cut to peices buy one of the previous owners im trying to repair it i might end up getting a new loom
[Edited on 20-01-2011 by kylesri]
|
pow
Premium Member
Registered: 11th Sep 06
Location: Hazlemere, Buckinghamshire
User status: Offline
|
Single back wire is ignition live
|
kylesri
Member
Registered: 13th Jan 10
Location: Technician At Perrys Vauxhall Canterbury Kent
User status: Offline
|
mines been cut but in this pic of sean-b's loom it has a plug on it and it looks like the same fitment to the plug on the oil sensor on the front of the sump mate
|
Generation
Member
Registered: 7th Jul 09
Location: Essex
User status: Offline
|
Ignition live
|
kylesri
Member
Registered: 13th Jan 10
Location: Technician At Perrys Vauxhall Canterbury Kent
User status: Offline
|
where do i run it too mate do you no
|
pow
Premium Member
Registered: 11th Sep 06
Location: Hazlemere, Buckinghamshire
User status: Offline
|
As far as I know you need to run it to the 9 pin plug in the drivers footwell. Someone will confirm though
|
kylesri
Member
Registered: 13th Jan 10
Location: Technician At Perrys Vauxhall Canterbury Kent
User status: Offline
|
cheers mate now got to sort the wiring out for the oil sensor in the front of the sump as the wiring for thats no where to b seen or do you actual need it plugged in can i leave it unplugged
[Edited on 20-01-2011 by kylesri]
|
Generation
Member
Registered: 7th Jul 09
Location: Essex
User status: Offline
|
Mines not runnig, and doing same conversion as you at moment. these answers had of here in last few days.
Pow is right, runs to footwell.
Oil sensor not needed in corsa, only needed for cavs and claibrad IIRC
|
kylesri
Member
Registered: 13th Jan 10
Location: Technician At Perrys Vauxhall Canterbury Kent
User status: Offline
|
cool cheers for the help everyone are you using the corsa starting and chatging loom on yours
[Edited on 20-01-2011 by kylesri]
|
pow
Premium Member
Registered: 11th Sep 06
Location: Hazlemere, Buckinghamshire
User status: Offline
|
Yeah don't use the oil level sensor
|
Sean-B
Member
Registered: 1st May 07
Location: Wolverhampton Drives: 200SX S14a
User status: Offline
|
That's my picture 
Have you got a coilpack engine? If so have you got an ignition amplifier?
|
Generation
Member
Registered: 7th Jul 09
Location: Essex
User status: Offline
|
Yeah, had to buy one these too, after lots of ringing about got from
Motor factors for about£40
|
kylesri
Member
Registered: 13th Jan 10
Location: Technician At Perrys Vauxhall Canterbury Kent
User status: Offline
|
yeh have got a coil pack engine sean well ive paid boz gsi for one hes recieved the check but i havnt recieved the part yet have you got a spare then
|