mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Can someone nip out & measure a corsa b tilt & slide sunroof?
Please measure the gap size, not the glass size.
I would, but mine is like 15 miles away locked up in my dads garage, need to get a carbon sheet, but dont know what size i need.
Cheers.
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Come on guys and gals, its a two minute job!
50p in your paypal account for whoever does it first
|
am4nf
Member
Registered: 27th Jul 08
Location: South Ayrshire Drives: Corsa Sport
User status: Offline
|
is ur car not outside? lol
|
Root
Member
Registered: 28th Dec 08
User status: Offline
|
I would, but it's almost midnight.
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
You're lucky i'm bored
83cm x 44cm
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
And I will add it's freezing outside right now, Although only wearing a pair of shorts was a dumb idea
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Cheers Terry, whats your paypal addy so i can deposit said 50p?
Thanks very much matey!
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Oh, one last measurement please!
Can someone measure the gap between the edge of the sunroof hole to the plastic bits for the roof rack, and from the front edge to the edge of the windscreen rubber.
All will become clear!
Oh, and again, i have no access to my car until next week & need this ordering asap!
Another 50p to be had here!
Cheers
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
Don't worry about it mate, Only takes a minute to do.
From edge of sunroof to top of windscreen is 21cm.
From side of sunroof to edge of roof trim is 4.7cm each side.
In case you needed it from the back of the sunroof to the back edge of the roof is 76.5cm
I should point out the measurement to the top of the windscreen was taken in the middle point as it's shorter than 21cm towards the ends of the windscreen as the line curves.
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Spotty dog, Hero!
Cheers matey.
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
No probs fella, Gave me an excuse to flash my legs to the neighbours again and do a few bits on the car
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
And i'm curious as to what you have planned. Is this for a track car?
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Indeedy it is mate, this one...
Cheers again.
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
Looks good mate, Weight saving on the cards then
Is it an XE?
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Thats the plan, though i've spoken to mike at performance trim, and im now looking at getting carbon doorcards & stuff now
I blame you.
Yep, xe, just a few bits, sbd manifold, 2.25" system, cams, verniers, ported head.
Cant wait to drive the bugger, but got a hole in my roof at the min
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
That's pretty much my engine spec. Where did you get the SBD manifold from? I'm on the look out for one at the moment.
|
fazza
Member
Registered: 7th Feb 08
Location: Plymouth
User status: Offline
|
mark whats your plan for the roof then?
im stuck in the same boat mate
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Terry, i got it 2nd hand, was quite the bargain, got it heat wrapped now too.
Fazza, deffo going for a carbon sheet, just waiting on hearing from Mike @ PT, will drop you a pm when i hear mate.
|
fazza
Member
Registered: 7th Feb 08
Location: Plymouth
User status: Offline
|
legend cheers mate
u thinking carbon sheet for the whole roof or just to cover the sunroof hole?
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Just the hole, PT do a carbon skin, but out of my budget, the part im looking at will be around 100quid i think.
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
Can someone measure corner to corner, the gap, not the glass please?
last one, i promise!
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
Go on then i'll volunteer.
It's about 89.5cm. I'd overestimate slightly in all measurements if I were you so you get the right size and trim it if required
That's £1.50 you owe me
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
This is for the cross bracing that will go from corner to corner, so needs to be accurate matey.
So, so far we have...
Hole in roof...
Length 83cm
Width 44cm
Diagonal corner to corner 89.5cm
Cheers matey, come find me at one of the shows for a tinny
|
Terry12
Member
Registered: 24th Sep 07
Location: Manchester
User status: Offline
|
May well do that if you're at PV
|
mantamark
Member
Registered: 19th Jun 06
Location: Northumberland
User status: Offline
|
i'm going to try & get there matey.
|