AlexW
Member
Registered: 25th Oct 08
Location: Essex
User status: Offline
|
Bout funking time.
You won't need to change the fuel pump for going in your 1.0
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
Yea its about time really  , it was basicly ready, just had to pull the loom through and disconnect the fuel lines then drop it out.
Really  , I never checked to see but I was under the impression the 1.0s were SPI? Obviously not
|
AlexW
Member
Registered: 25th Oct 08
Location: Essex
User status: Offline
|
1.0's are MPI, and run the same fuel pressure as the bigger engined stuff.
[Edited on 15-03-2011 by AW06]
|
DansCorsaSXi
Organiser: Yorkshire
Premium Member
Registered: 13th Jan 10
Location: Worksop
User status: Offline
|
Nice one Jame 
Star silver C20XE SXi Project thread
Smoke Grey Corsa GSi Project thread
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
quote:
Originally posted by AW06
1.0's are MPI, and run the same fuel pressure as the bigger engined stuff.
Nice one , saves me a job then , cheers for the info 
quote:
Originally posted by DansCorsaSXi
Nice one Jame
Cheers Dan, it feels as if I'm getting somewhere now
|
AlexW
Member
Registered: 25th Oct 08
Location: Essex
User status: Offline
|
Ohhh, Something else I should point out, Don't forget to take the servo vacuum off the red one, Will be needed when converting, or at least be handy.
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
Whats that?  Do you mean the brake servo?
Me and my dad put it on its side tonight and got the exhaust off, so afaik its ready to go. Let me know if theres anything else I should remove before it goes 
|
N16K
Member
Registered: 4th Oct 04
Location: Belfast, NI Drives: Corsa D SRi, Tuned Cooper S, B
User status: Offline
|
nice job on the rear lights.
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
Finished removing a few odds and ends that I still needed/wanted so that brought the red one to an end Duke looks happy too
Dad went and got his beasty from work and tugged it out,
Peek a boo,
And its out, leaving its mark
Up,
Up,
And away,
Byeee 
Have to get started on the silver one soon , going to treat her to a spruce up tomorrow
|
SeanXE
Member
Registered: 17th Jan 09
Location: Luton
User status: Offline
|
Wooo its gone, now hurry up and finish the silver one!
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
Hold your horses
Will be be ordering timing belt kit and waterpump shortly along with gaskets and other bits, and get it all cleaned painted then I'll get onto stripping the silver one
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
Gave her a some TLC today, first one of 2011 I even spruced up the blacks
Fitted my NI-Vaux stickers too
Tucked up for the night
|
corsamon
Member
Registered: 18th Dec 08
Location: Lancashire
User status: Offline
|
looks bloody lovely mate, gloss black mirrors and trims i though would look great though?
Looks lovely and streight, no dents! JELOUS!
|
Daveskater
Premium Member
Registered: 29th Apr 08
Location: Oxford, UK Drives: Jap wagon
User status: Offline
|
Black and silver is a nice theme, rear lights set it off
At least half the people on here want their car as low as the red one when it left tbh.
Numberwang!
Originally posted by AlunJ
I like you Dave, you are a man of men
Originally Whatapp'd by Neo
Dave's maybe capable of a drive-by cuddle
Look at my pictures
|
DansCorsaSXi
Organiser: Yorkshire
Premium Member
Registered: 13th Jan 10
Location: Worksop
User status: Offline
|
This photo looks mint Jame! Really shiny,loving the black alloys on the black bumpers Looks really good mate,nice work
Star silver C20XE SXi Project thread
Smoke Grey Corsa GSi Project thread
|
SeanXE
Member
Registered: 17th Jan 09
Location: Luton
User status: Offline
|
Much better, the bumpers are black :O
|
Piér
Member
Registered: 4th Jan 10
Location: Gloucestershire
User status: Offline
|
Looking much better mate
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
Cheers lads appreciate the nice comments  , once I had done and took a step back I fell in love with it all over again
Just need to re seal the o/s headlight as it steams up every time water gets near it
|
David`
Member
Registered: 16th Dec 10
Location: Bedford
User status: Offline
|
I like that, looking good, just get your mirrors sprayed 
[Edited on 21-03-2011 by David`]
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
Cheers fella, they will be going silver in the near future , my main priority at the minute is to get the engine changed over
|
Minty_Fresh
Member
Registered: 1st May 08
Location: westmidlands
User status: Offline
|
new rear numberplate and numberplate light cover would freshen it up a treat..
[Edited on 21-03-2011 by Minty_Fresh]
|
Jamxe
Member
Registered: 26th Nov 08
Location: Ireland
User status: Offline
|
Top work fella, love the front end, looks really tight, gaps look factory perfect.. Love the theme too..
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
I never thought of that tbh, might go get one tomorrow actually
As for the number plate there is a bit of surface rust behind it that I want to sort before I put new plates on.
|
Jamie-C
Member
Registered: 3rd Jun 08
Location: Ballycastle
User status: Offline
|
quote:
Originally posted by Jamxe
Top work fella, love the front end, looks really tight, gaps look factory perfect.. Love the theme too..
Cheers matey , yea its all pretty straight, all panel gaps are the same like you said, only damage on it is the ding on the bottom of the drivers door and a small bit of rust on the boot. Other than that its all good
|
Callum
Member
Registered: 17th Dec 08
Location: Renfrewshire
User status: Offline
|
Get this done!
|
