corsadonk
Premium Member
Registered: 4th Jul 09
Location: Marlborough, Wiltshire
User status: Offline
|
quote: Originally posted by Richardhhha
you got the wrong cav td pipe then mate.. Could always ask sean-b where he got his hose from
Bugger That was a waste of £3
I'll take some measurements and see if my store man can get me one like sean-b has.
Thanks.
|
Sean-B
Member
Registered: 1st May 07
Location: Wolverhampton Drives: 200SX S14a
User status: Offline
|
Sean-B does have a nice pipe
|
jamesy1990
Member
Registered: 15th Dec 08
Location: fife
User status: Offline
|
just finished mine mate wasnt hard , just remember to buff 5-10mm off the bolt on the altanator bracket!!!
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
what extra pipes did you have to make james?
|
jamesy1990
Member
Registered: 15th Dec 08
Location: fife
User status: Offline
|
got a meter lengh of clear 3mm id hose from halfords and 3 t peices for the vacume network , for the intake pipe from mantzel to air box i managed 2 bodge one out of the standered air pipe just cut it jubileed it either end and drilled a hole for the air temp sensor works fine , als0o removed all my air con junk at the same time
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
i have a pipe with an air temp sensor in already
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
what was the o.d. of the hoses might be able to get some from work
|
corsadonk
Premium Member
Registered: 4th Jul 09
Location: Marlborough, Wiltshire
User status: Offline
|
Well done, what is it like?
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
ive not done mine yet
|
jamesy1990
Member
Registered: 15th Dec 08
Location: fife
User status: Offline
|
its like 5mm od hose !u can get it from halfords i needed a meter
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
need a quick answer please
is the original plastic intake bolted to something?
feels like it is
|
jamesy1990
Member
Registered: 15th Dec 08
Location: fife
User status: Offline
|
no its just the most stubern thing iv even come across! you will need to cut it at the air box side and at the gearbox side and it should come out with a bit of force! i cut it with a hack saw blade that i snapped in half! its a shitty job but its got to be done!
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
Yes it is bolted. There are 2 torx bolts holding it to the back of the bottom inlet
|
jamesy1990
Member
Registered: 15th Dec 08
Location: fife
User status: Offline
|
mines wasnt bolted
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
it was bolted like dean said and also did anyone else have a pipe heading downwards?
looks like it was blowing air onto the cat?
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
yellow - where does this go? whats it for?
blue - where does it start? ive got no connection near the servo?
red - where does it go?
the small coolant hose, do you connect that to the other hose further behind the engine?
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
Not sure on the yellow, looks like its going down towards where the throttle body used to be.
Blue is a vacuum pipe, looks like he has used a T-Piece and thats what the blue arrow is poiting at
Red looks like its coming off the fuel tank vent switch. ( I think thats what it is). On the standard manifold its clipped on the battery side. This pipe goes behind the bulk head and kind of follows the same course as the fuel lines.
[Edited on 19-02-2010 by dean101287]
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
sorted the red
the yellow on mine is blanked
and the blue i have no where to fit it to the mantzel! only has fitment for the servo
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
Do you have any items that need a vacuum and no place for them to get it off?
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
yeah
fpr
afm
ftvv
rocker cover
also there is a pipe coming from one of the inlet/outlets on the right hand side of the rocker
guessing thats not needed?
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
Strange how there is no vacuum take off on the mantzel. My dbilas had too many and I had to blank one off. Can you take the blank off the one thats labled yellow up there ^?
Also the picture above, he seems to have taken a vacuum off the brack servo pipe and then T-pieced it to where he needs.
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
quote: Originally posted by jamesy1990
just finished mine mate wasnt hard , just remember to buff 5-10mm off the bolt on the altanator bracket!!!
you can see there its not t pieced
i did look at using the one that was blacked off but didnt know if it would work
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
Yes you could use the one thats blanked off.
Whats not T-Pieced? The vacuum pipe looks like it coming off the union thats on the brake servo, then it has 3 T-pieces going off it.
|
IvIarkgraham
Premium Member
Registered: 27th Mar 04
Location: Ellesmere Port, Cheshire
User status: Offline
|
yeah
i thought you meant he had put a t piece in the brake servo
|
jamesy1990
Member
Registered: 15th Dec 08
Location: fife
User status: Offline
|
the bit of braided hose from the mantzel goes onto your egr valve , i blanked mine off but it still has a fitting attached for a vacume , the red is a vacume from the vual tank vent valve , it shouldnt be disconected at the other side as u shouldnt be anywhere near it , the blue is my vacume network , i have a little nipple that comes off the brake servo vacume on the mantzel , you run a racume from the mantzel to the rockercover nipple , then u cut it in the places and insert 3 t peices first one goes to map sensor on bulk head next to coolant bottle . second vacume goes to the fuel presure regulator and the third and final vacume goes to the fuel tank vent valve (little black box with blue and red plug )
|