jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
where do i make the holes above the taps connector or below and the same as the waste pipe theres no holes in the cupboard for the pipes to go through
[Edited on 10-02-2010 by jas-tec]
|
_Allan_
Member
Registered: 24th Mar 04
User status: Offline
|
I'm no plumber and have never done it before but surely you just use the braided pipes screwed in the water feeds (Green Circles) and wastes go to the Pink circles?. You will need to cut holes in the cuboard for the hoses though obviously.
I'm sure Matt or someone will confirm 
|
jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
yes i know but not sure where to cut the holes out above the green circles or below it any idears
|
_Allan_
Member
Registered: 24th Mar 04
User status: Offline
|
Sorry I thought ou were gonna start cutting into pipes. I'd cut higher up into the corner maybe if you have long enough connectors.
|
jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
yes too long to be honist mate.and same as the waste pipe yes
|
Colin
Member
Registered: 4th Apr 02
User status: Offline
|
Shouldnt matter, just whatevers easiest tbh. Mine go right up & through the gap where the drainer is & back down.
|
jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
all done just put pipes on and ready to see if it leaks
|
a_j_mair
Member
Registered: 23rd Jan 04
Location: Scotland
User status: Offline
|
makr sure you have remoived all bungs from the pipes or cut off any nibs on the waste conectors that need cut off
|
Gregor
Member
Registered: 28th Nov 03
Location: Paisley, Renfrewshire
User status: Offline
|
You would drill them above the fittings. Means the waste pipe bends to a u-shape before the waste
|
dannymccann
Member
Registered: 9th Aug 06
Location: Doddington, Lincolnshire
User status: Offline
|
quote:
Originally posted by a_j_mair
makr sure you have remoived all bungs from the pipes or cut off any nibs on the waste conectors that need cut off
+1 
|
Rickavo
Member
Registered: 2nd Jul 09
Location: Manchester
User status: Offline
|
Make sure you take the scews/bolts out the back that support the barrel otherwise it will be fubard after the first go
|
jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
i cant seem to now the seetings on it its a candy aqua 1200 yes course i am a man not a lady when u need one
|
jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
|
dannymccann
Member
Registered: 9th Aug 06
Location: Doddington, Lincolnshire
User status: Offline
|
Hot feed? How OLD is that washer???
Also your sentence makes no sense whatsoever, you want to ask again?
|
jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
its old yes all sorted now thanks every one
|
Ian
Site Administrator
Registered: 28th Aug 99
Location: Liverpool
User status: Online
|
Not sure that waste will flow OK, did you seal around or is it just pressed in?
|
jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
just pressed it in really.what about the wast pipe
where eles can it go the waste pipe
[Edited on 12-02-2010 by jas-tec]
|
Colin
Member
Registered: 4th Apr 02
User status: Offline
|
Its meant to push onto the tappered part - bit you've drawn the pink circle round!! Just trim the end off it with a hacksaw, or stanley if your carefull. Oh dear!!!
[Edited on 13-02-2010 by Colin]
|
jas-tec
Member
Registered: 10th Oct 05
Location: oxford
User status: Offline
|
ok i new that lol on the tape now. i know wheres a women when u need one
[Edited on 13-02-2010 by jas-tec]
|
