corb
Member
Registered: 24th Apr 02
Location: Calgary, Alberta, Canada
User status: Offline
|
|
Trotty
Member
Registered: 22nd Feb 01
Location: Bristol
User status: Offline
|
Getting there then dude 
I see a bit more sanding to go yet though? 
Still, gonna be worth it - will look ace once finished 
|
chillout
Member
Registered: 7th Apr 03
Location: on my own far far away from everyone!!!
User status: Offline
|
nice mate! are those to fit subs in? r they for 10's or 8 inch subs?
|
SteveW
Member
Registered: 15th Jul 02
Location: Up in the clouds
User status: Offline
|
 have you managed to get all of the wet filler off yet??
You poor bugger, looking good tho matey.
Finally got through to Anup, hes been a busy bugger opening a new bar/Club in London 
|
corb
Member
Registered: 24th Apr 02
Location: Calgary, Alberta, Canada
User status: Offline
|
Chiilout - errr  no! theyre 17cm, for some Focal 165K2's.
Steve - Not looked at them tonight, will have a go tomorrow.
He's gonna make it still tho i take it? else i'll help sort a sub out if u want?! He's gonna soooo fucking loaded, BASTARD!! Maybe we should all go up there at some point(depending what its like, eg, not Brixton or somewhere like that!)
|
beattie17
Member
Registered: 13th Dec 02
Location: perth Drives: 02 ibiza 20v turbo
User status: Offline
|
what r u goin to do with the lower plastic bit?u know ur door pocket
|
corb
Member
Registered: 24th Apr 02
Location: Calgary, Alberta, Canada
User status: Offline
|
putting it back on, cos i use the pockets for storage as i dont have a glovebox
|
beattie17
Member
Registered: 13th Dec 02
Location: perth Drives: 02 ibiza 20v turbo
User status: Offline
|
yeah but r u doing anything to them mate?
|
corb
Member
Registered: 24th Apr 02
Location: Calgary, Alberta, Canada
User status: Offline
|
might trim them in alcantara
|
Fear
Member
Registered: 20th Nov 02
Location: Down off the hill
User status: Offline
|
Does it matter the size of the enclosure on door builds
Cuz i was gonna do some in original speaker place but was gonna block the hole into door over to try and stop treble escaping outside the car as i cant stop it
Looking good by the way Is that all resing and body filler
|
corb
Member
Registered: 24th Apr 02
Location: Calgary, Alberta, Canada
User status: Offline
|
yeah, tis all fibreglass and filler(on top of original doorcard)
dont seal them into an enclosure, let them use the whole door. Just get some dynamat in there. Thats what i've done, bit of a bitch getting it between the door and side impact bars but got there in the end.
|
Fear
Member
Registered: 20th Nov 02
Location: Down off the hill
User status: Offline
|
So what about your builds are you gonna cut the back out behind the speaker cuz it looks like you got an encloser going on there
|
corb
Member
Registered: 24th Apr 02
Location: Calgary, Alberta, Canada
User status: Offline
|
i will HAVE TO cut the back out behing the speaker(had planned to do that anway!) as theres nowhere near enough depth, the bit i ddnt want to do, which i MAY have to is to cut a hole in the actual door, will find out once finished though.
|
wayne hiscock
Member
Registered: 20th Jan 01
Location: wiltshire, trowbridge
User status: Offline
|
jesus stay away from pot holes.
i'd be scared to drive with that much filler
wots goin in there 17cm or 8" sub?
|
