Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
the fucker wont come off!
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
cut it off if u dont wanna keep it! i twatted mine with a rubber hammer, or is it the one i send in the post?if so i couldnt get it apart but few it thru the car like that!
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
old one i tried cutting it but jigsaw wont/cant do it
im gonna twat it with a chisel and hammer
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
use a hack saw u lazy bugger! wont take 10mins to cut thru it!
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
quote: Originally posted by Adam-D
old one i tried cutting it but jigsaw wont/cant do it
im gonna twat it with a chisel and hammer
open up the flanges on it with hammer and chisel, then it shud come off, but cutting it will be quicker IMO
|
mike_1.2LS96
Member
Registered: 23rd Oct 03
Location: Darlington | Mazda 323 1.8 Exec
User status: Offline
|
Angle grinder it off.
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
quote: Originally posted by mike_1.2LS96
Angle grinder it off.
give me a grinder and i will
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
junior hacksaw it is
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
i want
a. bigger hacksaw
b. one of them reciprercating saws like on scrapheap challenge
im fucked its an effort to lift ma arm
think ill havve some breakfast then fit the new one after a little rest
|
mattyboy199
Member
Registered: 5th Feb 03
User status: Offline
|
careful you don t break the centre box pipe i have done this before pissed me off to. Go kwik fit get em to do give a tenner or something.
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
its off mate centre box is ok just gotta fit new system now no way im paying a garage to do it
i done every thing on ma own car meself
apart from the tints
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
u got it off then lol! the bore is a tad bigger on your new one aint it!
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
just a little
its on clamped up
the rubbers dont match up the same as the old one? so gona have a play with it
|
PaulW
Member
Registered: 26th Jan 03
Location: Atherton, Greater Manchester
User status: Offline
|
was it a universal fit box or one for the corsa?
could just be a case of swapping the left & right rubbers or using the centre hole in them instead of the ones on the edge
just dont do what I did once & do it sooo tight that it pushed against the rear bumper & melted it
|
DanielJ
Member
Registered: 21st Nov 01
Location: gwent, south wales
User status: Offline
|
go and get shorter rubbers
|
PaulW
Member
Registered: 26th Jan 03
Location: Atherton, Greater Manchester
User status: Offline
|
ooooh also just slacken off the clampso its free to move, then do the rubbers at the back, get it in position & tighten up clamp, sometimes helps a hell of alot doing it that way
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
na it clears the bumper
i put one rubber on its side to raise that edge u know the clips that hold the rubbers on? they dont line up on the newun so as its rubber am gone force it on the new zorst dont have little rings for the clips? so............cable ties?
|
PaulW
Member
Registered: 26th Jan 03
Location: Atherton, Greater Manchester
User status: Offline
|
nah usually the end of the lil supports on the backbox have bits bent down
-----\
something like that, txt is shite to draw in so usually they stick on through that, plus when the rubbers are attached to the mounts on the rear of the car & the clips are on, they dont move much as the backbox cant slide back cos of the system
dont use cable ties, they might melt aswell!
when I had a rage box (universal one) I had to weld on a bolt to the fitting plate which was sposed to be for the corsa, never was right though!
TBH only decent fit I got was from a peco BB2 exhaust I had on once, and no it wasnt as bad a box as people say!
[Edited on 11-01-2004 by PaulW]
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
i used cable ties on ma last zorst i had to cut em off to remove it
its a scorpian full system ss grp a
getting ma breakfast now---- then ill finish it off
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
i had probs getting some rubbers for it, ment to say i ended up using some ford ones, they work a treat! fiesta i think! then just force them on, little clips? i think i no what u mean, didint use them on mine in the end, to hard to fit on lol! just have to play with it to get it to fit
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
its ok when i get some energy ill clear up ma tools and take it outta the garage
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
u had it running yet? sound much better than ur old system?
|
Adam-D
Member
Registered: 11th May 02
Location: Cheshire
User status: Offline
|
tested it a little well stated it up whatced ma front wheel spinning - it was off the floor give it a lillte revs cant test it till its on the road and using its power
sounds suble on idle thou-like it
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
nice, yeah sounds so much different under load!
|
starkmotorsport
Member
Registered: 27th Apr 02
Location: Scotland
User status: Offline
|
Your meant to heat one part of the exhaust so that the metal expands, hence it slips off easy.
|