Ant B
Member
Registered: 4th Jan 09
Location: Woodford Halse, Northamptonshire
User status: Offline
|
hi i am currently preperring my bonnet for respray and i have took the two wiper washer jets out and whot would be the best way to fill the hols in,and allso were would i get two wiper arms with washer jets on,thank you very much
|
Ste
Premium Member
Registered: 5th Mar 03
Location: Taif, Saudi Arabia
User status: Offline
|
keep them and fit phase 2 pug 206 fan jets 
I would rather lose by a mile because i built my own car, than win by an inch because someone else built it for me.
|
dale_sri_2009
Member
Registered: 10th Jan 09
Location: Upton/Wirral
User status: Offline
|
cut a piece of card bourd out an celotape it under the holes then fiberglass over then remove the cardbourd then sand the fiberglass then filler over it but ste ws idea sounds good 
|
Ant B
Member
Registered: 4th Jan 09
Location: Woodford Halse, Northamptonshire
User status: Offline
|
ok thanks but i was thinking about sellotaping some cardbord undernegh and just filling the hole up whif filler would thatt work
|
ShEp
Member
Registered: 9th Aug 05
Location: Dingwall, Highland
User status: Offline
|
fibre glass the front of the hole
then etch the rear, (cut unto the metal)
etch the edges of the hole going into the fibreglass slightly, do this front and back and the fill, it will give the filler something decent to grip to, as it will just fall out if you only fill it from the off.
|
Ant B
Member
Registered: 4th Jan 09
Location: Woodford Halse, Northamptonshire
User status: Offline
|
i carnt keep them as have alredy pulled them out and all the pipes is it a hard job to fill
|
Ste
Premium Member
Registered: 5th Mar 03
Location: Taif, Saudi Arabia
User status: Offline
|
It is easier to put new pipes there mate. To get a perfectly flat finish and then whole bonnet painted isn't going to be cheap or easy!
I would rather lose by a mile because i built my own car, than win by an inch because someone else built it for me.
|
dale_sri_2009
Member
Registered: 10th Jan 09
Location: Upton/Wirral
User status: Offline
|
i agree but dont just filler over it coz as soon as you slam the bonnet it will crack den you will have to repsray the hole bonnet bin there dne that
|
Sean-B
Member
Registered: 1st May 07
Location: Wolverhampton Drives: 200SX S14a
User status: Offline
|
quote:
Originally posted by Ste W
keep them and fit phase 2 pug 206 fan jets
do they fit in the standard holes?
are these them? clicky
|
Ste
Premium Member
Registered: 5th Mar 03
Location: Taif, Saudi Arabia
User status: Offline
|
They're the ones sean, they are as fook. I fitted them to my phase 1 GTi.
I would rather lose by a mile because i built my own car, than win by an inch because someone else built it for me.
|
Ant B
Member
Registered: 4th Jan 09
Location: Woodford Halse, Northamptonshire
User status: Offline
|
do them 206 fan jets fit in the standerd holes then,cus ar order some,and also what holdes them in place on the bonnet cus i just put a scredriver in the old one and think i broke them
|
Ant B
Member
Registered: 4th Jan 09
Location: Woodford Halse, Northamptonshire
User status: Offline
|
bump
|
Ste
Premium Member
Registered: 5th Mar 03
Location: Taif, Saudi Arabia
User status: Offline
|
I can't be 100% that they fit but you can certainly make them fit, even if you have to remove the clip and bond it in from behind.
I would rather lose by a mile because i built my own car, than win by an inch because someone else built it for me.
|
euro-dee
Member
Registered: 3rd Apr 09
Location: newcastle
User status: Offline
|
i wudnt fibreglass or bdge , it will crack in time , waste of time , weld it and skim filer but still after a while will crack lol , just leave em lol
|
