valver dove
Member
Registered: 11th May 11
User status: Offline
|
hello all im new to the site and im doing a little research as im thinking of putting the 20xe from my astra gte into my corsa run about whilst the gte gets restored im aware off most of the mods a need to carry out but unsure on others
aware of
1 corsa gsi/sport /tigra x16xe 22slipne drive shafts with 2.0l inner cvs on those for drive
2 256 gte discs n calipers witch i have
3 strenthening plate for lower cross member
4 off side engine mount bracket type 1 from ebay as my shell is 8valve c12nz engine
5 lowering blocks for roll bars
6 ecotec throttle body adaptor plate and pipe
7 gearbox rear mount spacers
i think thats it to get the engine in and 90% ready to rock obviously wire in and mod original exhaust to fit four branch
im unsure if the 1.2 in tank fuel pump is gunna cut it fueling the 20xe can any 1 confirm that
its fine to use just unsure A MEAN IM ONLY DOING THIS FOR THE FUN FACTOR FOLKS
few pics of the beast lol



engines power quite healthy a do say myself should go well in corsa lol


|
grubz172
Member
Registered: 14th Jan 10
Location: Manchester Drives: Vehicles
User status: Offline
|
-you use a fuel pump from an mpi corsa so a 1.4/ 1.6 sport fuel pump will do
-you use cav mk2 1.6 inner c.vs not 2.0 ones
- up to you whether you strengthen it or not as you dont really need to unless its an let
but everything else is right on your list
also check stu_c's 5 door c20xe. same colour as that so will give you some ideas 
http://www.corsasport.co.uk/board/garage.php?action=usergarage&owner=stu_c&carid=8013
[Edited on 16-05-2011 by grubz172]
|
Corsa_Sport21
Member
Registered: 13th Apr 08
Location: Leven, Fife. Drives : 205 GTi
User status: Offline
|
Whats been done to the engine??Deffo not standard,not with near enough 180lb/ft torque.
|
valver dove
Member
Registered: 11th May 11
User status: Offline
|
hello cheers for the reply my freind put x25xe lump in his astra mk3 1.4 single point injection and the engine ran fine so am curious if it will be ok
|
valver dove
Member
Registered: 11th May 11
User status: Offline
|
honest m8 its totaly standards a mean a opened the ecu standard chip in and theres no receipt for cams in it its the early 20xe with lighter cranck and mayle forged pistons they are 156bhp with the fp ecuive polished the throttle body and matched the inlet manifold to the head thats it and that was after the rolling road session its just over 100k so just well healthly
|
Corsa_Sport21
Member
Registered: 13th Apr 08
Location: Leven, Fife. Drives : 205 GTi
User status: Offline
|
Why not just keep it in the Astra??You had the Astra for a while like??
|
valver dove
Member
Registered: 11th May 11
User status: Offline
|
well im taking it out of the astra cos im getting the thing fully sprayed somtime in the distant futre so it just gunna be sitting there the engine so gunna use it in the corsa for a while
|
Crana
Member
Registered: 20th Jan 09
Location: Newcastle
User status: Offline
|
170bhp from and engine that came with 156 standard? Rollers must be out I have an xej as well and it got 142.1bhp and 136.8lbf 100% standard only done one run at college
|
am4nf
Member
Registered: 27th Jul 08
Location: South Ayrshire Drives: Corsa Sport
User status: Offline
|
pics of astra needed tbh 
Also is a diesel rad not needed?
|
valver dove
Member
Registered: 11th May 11
User status: Offline
|
quote: Originally posted by Crana
170bhp from and engine that came with 156 standard? Rollers must be out I have an xej as well and it got 142.1bhp and 136.8lbf 100% standard only done one run at college
well my freind has a clio 182 cup wit decat and full scorpion and filter
and the gte is on par except for 5th where the gte starts to pull on the 182 so you be the judge m8
|
Crana
Member
Registered: 20th Jan 09
Location: Newcastle
User status: Offline
|
must be a one off 20xe that vauxhall made then? :S must have cams or something to make over standard power?
|
valver dove
Member
Registered: 11th May 11
User status: Offline
|
quote: Originally posted by Crana
must be a one off 20xe that vauxhall made then? :S must have cams or something to make over standard power?
forgot to mention m8 it has a ashley enlarged four branch but the rest of the engine internals is standard it has airbox with k&n panel filter thats it
General performance pointers on the C20XE and LN exhaust manifolds
So, how do you set about tuning C20XE and LN engines? Well, step number one is replacing the standard exhaust manifold, as the standard item was designed to maximise low-end torque. At high revs this becomes a restriction, so it's critical that it's upgraded at the earlist opportunity. Steve explains - "Apparently the first pre-production engines from Cosworth produced 170bhp as standard but they wanted more torque for the road which they got by making the manifold's pipes smaller. This also helped reduce emissions by keeping the gas speed up, but when you get up to the top end it becomes a restriction."
http://www.sbdev.co.uk/History_files/History_BudgetHorsepower.htm
have a read pal
|
Crana
Member
Registered: 20th Jan 09
Location: Newcastle
User status: Offline
|
So my xej will make 170 if I fit a large bore 4-2-1? Mine is getting dyno'd soon again made 142.3bhp last time with the exhaust hanging off dyno has since been calibrated because it was out quite abit when you put a brand new land rover on and it made well under its spec lol since had a group n chip fitted and a 2.25'' system made hoping for 150bhp cheers for the link reading it now
|
valver dove
Member
Registered: 11th May 11
User status: Offline
|
all c20xe/xej /20xe all slight differences in the way they are made will be different a mean their not blueprinted engine and some have had there back teeth ragged out a would of thought urs would of cleared over 150 with power cap and come plus chip on easy a mean all exhaust system perform different boxes create back preasure to suck gasses out quick so straight through pipes are crap a mean the gte had ashley four branch then standard all the way so helps wit torque

[Edited on 20-05-2011 by valver dove]
|