jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
Done a search and could not find any answers to what im looking for so here goes.....
On my 9 wire multiplug ive linked all the wires colour - colour and am left with......
Corsa Car loom
Thick Red
Thick Black
Calibra 16v Engine loom
Thin Black Red Trace
Thin Red - White Trace
Thin Black - Red Trace
Thin Black - Brown trace
Thin Blue wire
Can anyone tell me what wire i connect to what to complete the connection.
Cheers
|
p16vlv
Member
Registered: 15th Jun 02
Location: rossendale
User status: Offline
|
have you put the corsa loom that goes to starter motor and alternator on or used the calibra one . you have to use corsa one.
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
yes ive used the corsa loom to the engine starter, alternator and rev light switch etc etc
Its just the 9 pin plug next to the ECU location in the drivers footwell
|
p16vlv
Member
Registered: 15th Jun 02
Location: rossendale
User status: Offline
|
if you have no luck with your problem i will see a lad tonight who did all my wireing for me , its a bit risky if youre not sure.
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
ttt plz hlp
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
any ideas ppl?
|
quiksilver106
Member
Registered: 28th Jul 03
Location: LEEDS, UK
User status: Offline
|
You havent connected any wires in car??? think we connected 6/7 when we did mates corsa, was just a case of matching wires up.
only connected 3 on multiplug
[Edited on 01-09-2003 by quiksilver106]
|
quiksilver106
Member
Registered: 28th Jul 03
Location: LEEDS, UK
User status: Offline
|
thin blue wire on calibra loom is coolant sensor if i remember correctly and there should be thin blue in car on corsa loom. black/brown is a diagnostic one and that too should be in car on corsa loom.
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
i have matched all colours in car and am left with
Thick Red
and Thick Black
where do these go?
|
quiksilver106
Member
Registered: 28th Jul 03
Location: LEEDS, UK
User status: Offline
|
dont think thick red goes anywhere, thick black is ECU live and needs a 12Vignition feed. might need to run new wire for it then crank it over, hehe
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
cheers mate
anyone kno what the thick red is for anyway, whether its needed or not!
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
ttt
|
lee mitchell
Member
Registered: 26th Jan 01
Location: kent...drive's: eveyones conversion cars hard lol
User status: Offline
|
use the corsa starter motor loom. that will hae a plug on the end that plugs into the original place. ur then left with 9 wires in the drivers footwell and 9 wires on the 2 litre loom by the header tank or near the ecu depending on loom. all u have to do is extend the wires from the ones in the footwell to the 2 litre loom. colour to colour
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
cheers lee,
but on the 9plug connection in the footwell im left with
Thick Black
Thick Red
Where do i connect these as there aint a corresponding colour on the 2litre loom
|
lee mitchell
Member
Registered: 26th Jan 01
Location: kent...drive's: eveyones conversion cars hard lol
User status: Offline
|
there always is when i do them. il try and look 2nite
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
anyone else kno what the
Thick Black
and
Thick Red
mean and where theyre meant to go?
|
jjcymru
Member
Registered: 28th May 02
Location: ammanford,south wales
User status: Offline
|
any more info appreciated.
Cheers
|
