corsapaul16v
Member
Registered: 8th Apr 06
User status: Offline
|
what coil shud i use to run my throttle bodies? the wiring harness is alpha with a 4 pin plug, i have tryed to run a 16v corsa coil pack but it doesnt fire. tested the feeds against another 16v corsa and there arse about face. there is two switched lives coming from the ecu and im assuming the two earths that come from the amplifiers are the triggers. iv got a ford coil but it only has three pins and was wondering if any body knows how 2 convert them 4 wires to three or if there is a vauxhall coil that has four pins that would run it. thanks
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
need an un-amplified coil pack i.e from a focus 1.8 16v. not too clued up on 3 pin coils but I hope u didnt damage the ecu when attempting to use the corsa one. I know a lad that tried that (after many warnings not to) and he damaged the ecu. that was a webber alpha one as well.
have you tried cranking the engine while testing the coil feeds with a multimeter?
|
corsapaul16v
Member
Registered: 8th Apr 06
User status: Offline
|
got a mondeo 1 i believe they are the same. i have tested them witha test lamp, what should i b lookin for with a multimeter?
|
RobHayes
Member
Registered: 6th Sep 03
Location: Lincolnshire
User status: Offline
|
not sure if this helps?
i used it to remove a 3pin plug and fit a 4pin one onto my loom. just note what wire goes to what pin etc
|
broster
Premium Member
Registered: 6th Dec 02
Location: Drives: E39
User status: Offline
|
im running an st170 coil pack, unamped. its 3 wire, as for converting, im unsure, does the ecu not have instructions? i know mine did. we tried the corsa one with my ecu and it didnt work.... no damage was done
|
corsapaul16v
Member
Registered: 8th Apr 06
User status: Offline
|
wot coil are u using then rob?
|
corsapaul16v
Member
Registered: 8th Apr 06
User status: Offline
|
broster, if u used a corsa 1 then it must have been 4 pin plug rite?
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
i used a corsa one. broster is using a focus one.
my ecu didnt require an unaplified coil to be used
|
RobHayes
Member
Registered: 6th Sep 03
Location: Lincolnshire
User status: Offline
|
im using that one, which can be bought from SBD, most likely means its shoot
|
corsapaul16v
Member
Registered: 8th Apr 06
User status: Offline
|
that a 4 wire 1 rob. any part number on it mate
|
RobHayes
Member
Registered: 6th Sep 03
Location: Lincolnshire
User status: Offline
|
its a 4 pin plug, that has 3 wires but i also could of used a standard corsa one, as i had one before. this just came with my new kit so i've used it. and its cold and rainy outside so no part number other than sbd's part number on the website COIL4
|
corsapaul16v
Member
Registered: 8th Apr 06
User status: Offline
|
dave what do u mean by urz didnt require a unamplified 1. has it got a built in to the ecu. an amplifier i mean
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
most aftermaket ecu's requre an unamplified coli pack to be used. my ecu was bought from a vaux tuning specialist and are made by the maufacturer(omex) to be used with a standard coil pack which is amplified.
|