N90ATH
Member
Registered: 10th Sep 03
Location: Boreham, Essex
User status: Offline
|
Right just done a engine change on my corsa
Took old lump out swap all ancillaries and sensors etc on to the new block and head
Made sure everything connected and all pipes on tight
Went to start getting fuel and its turning over but not sparking 
Checked timing its fine, have been replacing icv, camshaft and crank sensors, tps, coil pack
And still nothing 
Anyone got any ideas?
|
Generation
Member
Registered: 7th Jul 09
Location: Essex
User status: Offline
|
What engine before and after
[Edited on 04-03-2013 by Generation]
|
N90ATH
Member
Registered: 10th Sep 03
Location: Boreham, Essex
User status: Offline
|
Both x14xe
|
Generation
Member
Registered: 7th Jul 09
Location: Essex
User status: Offline
|
Engine management light on?
|
N90ATH
Member
Registered: 10th Sep 03
Location: Boreham, Essex
User status: Offline
|
Yer engine management light comes on when ignition is on but when u turn the key just turns over no spark
|
Darryl H
Organiser: South Central Premium Member
Registered: 19th Nov 09
Location: Camberley Drives: Porsche 944
User status: Offline
|
Got an immobilizer?
My 944 had a fault similar and turned out to be the ECU had a fault with it
|My Corsa|SC|My Instagram|
|
N90ATH
Member
Registered: 10th Sep 03
Location: Boreham, Essex
User status: Offline
|
Yer have a immobilizer
|
Darryl H
Organiser: South Central Premium Member
Registered: 19th Nov 09
Location: Camberley Drives: Porsche 944
User status: Offline
|
Is there a way you can bypass it?
|My Corsa|SC|My Instagram|
|
N90ATH
Member
Registered: 10th Sep 03
Location: Boreham, Essex
User status: Offline
|
Well tried new ecu and new immobiliser and still nothing haven't got a clue nothing seems to work
|
Generation
Member
Registered: 7th Jul 09
Location: Essex
User status: Offline
|
Are you using a matching key chip ecu and transponder?
|
N90ATH
Member
Registered: 10th Sep 03
Location: Boreham, Essex
User status: Offline
|
Yer got everything from car new engine come from is there a way to remove the immobiliser
|
Generation
Member
Registered: 7th Jul 09
Location: Essex
User status: Offline
|
It's only going to be a standrd immobiliser error if the eml light is flashing
[Edited on 06-03-2013 by Generation]
|
N90ATH
Member
Registered: 10th Sep 03
Location: Boreham, Essex
User status: Offline
|
Ok not flashing
|
mattievRS
Member
Registered: 20th May 06
Location: Leicester
User status: Offline
|
Coil plugged in on underside of the black box on side of engine?
|
Generation
Member
Registered: 7th Jul 09
Location: Essex
User status: Offline
|
:/
|
shelidz
Member
Registered: 7th Nov 09
Location: Deeside
User status: Offline
|
Hmm weird one, so getting fuel, no spark...
Coil all connected correctly?, leads on, plugs etc.
all wires connected on the engine loom to the main loom?
Whats the error code on the dash mate, any way you can read it?
|
johnhara1
Member
Registered: 19th Oct 06
Location: Newcastle upon Tyne
User status: Offline
|
Why did you use the ecu, chip and transponder from the doner car and not your own if it's the same engine?
|