mattievRS
Member
Registered: 20th May 06
Location: Leicester
User status: Offline
|
What does this do exactly and if it had 3mm play from left to right(whilst looking at it) would it cause the car to feel like it was missfiring low down in the revs?
|
Richardhhha
Member
Registered: 29th Sep 07
Location: Croydon, Greater London
User status: Offline
|
ummm end float is way out there man.
if its deflecting that much you might need to be looking at bottom end rebuild or new block if the engine dont ahve thrust washers
|
mattievRS
Member
Registered: 20th May 06
Location: Leicester
User status: Offline
|
It seems that the pulley has enlarged itself somehow, as the key way on the timing pulley at the bottom is fine but the actual crank pulley has opened itself out.the pulley doesnt move towards or away from the block it moves forwards and backwards to the front and rear of the car about 3mm either way due to the enlarged keyway on it! i cant understand why this has happened but i think it may be the cause of a few issues on my car!ie starting then stalling,starting and driving then dumping the clutch and it cutting outfeels like its jerking sometimes on and off the accel and not picking up revs from 1000 to around 2500 very quickly.
[Edited on 03-12-2007 by m17tty]
|
luke85
Member
Registered: 26th Nov 07
Location: Chesterfield
User status: Offline
|
Yeah that could cause the problem because the RPM sensor gets its signal from the teeth on the outside of the pulley (on most vaux engines, whats in yours?)
I wouldnt drive it with a loose crank pulley, is the nut tight in the middle? if it comes off theres nothing to hold the bottom pulley for the timing belt on and that can come off which will really ruin your day
|
Badgersport
Member
Registered: 9th Apr 04
Location: Wolverhampton
User status: Offline
|
The exact same thing happened to me on my C16XE. The syptoms i had was bogging down and missfire. There was also a serious lack in power.
Ste
|
mattievRS
Member
Registered: 20th May 06
Location: Leicester
User status: Offline
|
its an x14xe mate,i took the crank pulley of and the bolt was probably finger tight to be honest but have torqued it up until i can get one from vaux.I reckon it is the crank pulley to be honest as i remember someone on here with similar probs not so long ago.And the pulleys fooked anyway so its gonna need a new one either way!
|
luke85
Member
Registered: 26th Nov 07
Location: Chesterfield
User status: Offline
|
Keep a close eye on it until its sorted mate, dont want the cambelt coming off because the bottom pulley slides out!
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
or try and ring Vsport to try and blag some free advice
|
Nic Barnes
Member
Registered: 5th Apr 04
Location: nowhere near ginger people
User status: Offline
|
quote: Originally posted by Dave A
or try and ring Vsport to try and blag some free advice
i do that but oddly when the fella that sounds like you asks whos calling you claim your not in.
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
im never in when you call, I hide in the toilet under the sink.
|
Nic Barnes
Member
Registered: 5th Apr 04
Location: nowhere near ginger people
User status: Offline
|
to be honest if i was you id not want to talk to me either. even if i will have to give you some more money.
|
mattievRS
Member
Registered: 20th May 06
Location: Leicester
User status: Offline
|
quote: Originally posted by Dave A
or try and ring Vsport to try and blag some free advice
but we could talk all day and you wouldnt make any money!!!!
cant blame me for trying!!!
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
wasnt me you spoke to so cant comment on what you were told tbh.
|